Got board so i cut a hole in the case

GnomeWizarddGnomeWizardd Member 4 LifeAkron, PA Icrontian
edited February 2005 in Hardware
I think it turned out ok!

Comments

  • madmatmadmat
    edited February 2005
    Looking good man, nice and clean.
  • NeoFXNeoFX Utah, US of A
    edited February 2005
    What brand/model case is that? Is that a full-tower? I could really use a case that size for my system!
  • GnomeWizarddGnomeWizardd Member 4 Life Akron, PA Icrontian
    edited February 2005
    its a coolermaster CM stacker I love it plenty of room
  • LINLIN Tri_State Area
    edited February 2005
    and how long did that take you to do?


    LIN
  • youvegotjermzyouvegotjermz Baton Rouge, La
    edited February 2005
    hey gnome! where did you get your power supply?
  • ZuntarZuntar North Carolina Icrontian
    edited February 2005
    Very nice Gnome!! :thumbsup:

    I can't wait to do mine!!! I never cut mine out from when i posted this thread.
    The design has changed slightly and about 20 times, but I think the final rev. is going to be it!

    BTW Gnome, what Graphics card is that, I remember reading sumthin about that cooler.
  • HawkHawk Fla Icrontian
    edited February 2005
    Sweet! Shows off all the cool stuff.
  • GnomeWizarddGnomeWizardd Member 4 Life Akron, PA Icrontian
    edited February 2005
    Ok first total of 1 hr cutting taping off and all
    Second- Power Supply was givin to me by Hank the owner at www.performance-pcs.com i go up there once a month or so for a visit
    Third - ITs a gigabyte 6800GT oc'ed to an Ultra
    And fourth - thx hawk i love it too
  • LINLIN Tri_State Area
    edited February 2005
    much obliged for the info :)


    LIN
  • NebulousNebulous New York, The Empire State
    edited February 2005
    Sa-weeeet job GW! I wonder if I send you my side panel to my back-up chieftec case you'll do that to it? :cool:
  • GnomeWizarddGnomeWizardd Member 4 Life Akron, PA Icrontian
    edited February 2005
    sure u gonna pay shipping both ways?
  • NebulousNebulous New York, The Empire State
    edited February 2005
    Sure, i don't have a problem with that :cool:
  • Geeky1Geeky1 University of the Pacific (Stockton, CA, USA)
    edited February 2005
    You're more dedicated than I am Gnome... if I were gonna put a window in either of my Stackers, I'd just take out the circular mesh grill and put a window in that... i mean it doesn't get much easier than a pre-cut hole :haha:
  • aspire-comptechaspire-comptech New
    edited February 2005
    I got the same question as nebulous think you could do the same for my Half Life Case. I would gladly pay shipping to wherever the hell you live.
  • Geeky1Geeky1 University of the Pacific (Stockton, CA, USA)
    edited February 2005
    Sounds like you've got a business opportunity here Gnome. Should quit construction and start charging people $50 to cut a hole in their case. :haha:
  • GnomeWizarddGnomeWizardd Member 4 Life Akron, PA Icrontian
    edited February 2005
    lol

    Catch me on AOL guys

    Actually it is where the mesh was Geeky. I just enlarged it. I wanted to put a round window in with aluminum rivets BUT this window was free :)
Sign In or Register to comment.