PDA

View Full Version : 2100 tbred bīs anyone?

TheLostSwede
9 Jun 2003, 01:43 AM
Iīd like to compare a little. Mine HATES voltages over 2.1. This thing wonīt even get into windows on that voltage, no matter what speed i have on the cpu.

This is what i have got so far: Itīs a 03/02 brown chip.

http://mackanz.no-ip.com/Cpu.jpg

Itīs not a contest or so, i just want to compare a little since i think my chip acts a little weird.

Oh btw, the hot board is because i dont have any casefans on. With a front 120mm fan, it get lowered by 4 or 5c, and so do the cpu.
Bad_Karma
9 Jun 2003, 09:59 AM
What the hell are you cooling that beast with?
Great Overclock! Too bad the 2.1 is the top.:thumbsup:
TheLostSwede
9 Jun 2003, 10:33 AM
Im using a Maze 2 Block, Aqua block on the radeon, and a dual 120mm Radiator. Nothing fancy.

Last time i checked, 2.4 wasnīt fully stable, but it seem to be now, i have been folding gromacs for 24 hours.

Thanks!
Omega65
10 Jun 2003, 01:03 PM
Nothing Fancy he says....

DUAL 120mm Radiator, Water cooled Vid card and CPU....

:D
TheLostSwede
10 Jun 2003, 01:15 PM
I think this cpu can do this an a good airsetup as well actually.
Gromacs and Prime 95 for 48 hours now. I think i have found the sweetspot on 1.90-1.92 V on this puppy.
Juggah0
10 Jun 2003, 08:05 PM
1700+ Tbred B JIUHB 0310, 2.13ghz @ stock vcore. and if a dual 120mm rad is fancy i guess my machine is roxor...


Nick
FormFactor
11 Jun 2003, 04:50 AM
I got my 2100 tbred b to that speed, but it would crash on the cpu test of 3dmark. So i dropped it to 2300 mhz with a 200 fsb...runs stable as hell. a little warm at just under 60 C . Its been foldin for months now without a reboot.

this is on pc3200 ram. kingston hyperx.
FormFactor
11 Jun 2003, 04:50 AM
I got my 2100 tbred b to that speed, but it would crash on the cpu test of 3dmark. So i dropped it to 2300 mhz with a 200 fsb...runs stable as hell. a little warm at just under 60 C . Its been foldin for months now without a reboot.

this is on pc3200 ram. kingston hyperx.
muddocktor
11 Jun 2003, 09:53 PM
Mack, your pic went south so I can't see what your oc is.

My 2100 is an AIUHB 0301MPMW and the highest stable overclock I've gotten out of it is 185X13 at 1.85v vcore air cooled. Actual vcore as per MBM was 1.92v. I generally run it at around 2250-2300 MHz and 1.75v vcore.
TheLostSwede
18 Jun 2003, 06:16 PM
Mud, the pic is up again. It seems that your cpu oc much better.

Why dont you put that watercooling on the 2100 instead?
panzerkw
28 Jun 2003, 04:00 AM
pfft I need to try raising the voltage to around 1.85 -1.90. Windows refuses to complete boot at 200 FSB x 11 on my 2100. 190 x 11 works though.