Here you are Gargoyle, EP-8KHA+ in action!

To talk on Icrontic, just register!

It only takes 30 seconds.

Have an account? Sign in:

Reply to Discussion

Options

muddocktor

Wandering about

6,250 Posts

13 Jun 2003, 10:56pm

Here you are Gargoyle, EP-8KHA+ in action!

Gargoyle, check out what the 8KHA+ can do d00d! It took that 2500 Barton like a duck takes to water. I didn't do any mods to the 2500 and still have it on low side multi's, so the max multi I can get is a 12.5 without hard coding a higher multi in on it, but that is easily done. Plus, if your hard drive and memory can take it, I've heard of these old boards going way past 166 fsb too.

Anyways, Barton is definitely doable on this old KT266A board.

Attached Thumbnails

Click image for larger version

Name: kha and barton.jpg
Views: 767
Size: 80.9 KB
ID: 933

__________________ I have some computers running Seti@Home.

Reply with Quote

FormFactor

Calm like a bomb!

1,381 Posts

29 Jun 2003, 12:45pm

Nice OC for a for a via chipset

__________________

Reply with Quote

Jamiro

New to the neighborhood

2 Posts

26 Jul 2003, 5:17pm

Hi muddocktor.
I've an epox 8hka+ too and I'm interested in buying a new barton processor.
I wolud like to recive recive some informations about your overclock such as the maximum multiplier that the motherboard let you set.
Please contact me on icq (49232507) on msn (joecamola@tin.it) as soon as possible.
(P.S Sorry for my bad English)

Reply with Quote

muddocktor

Wandering about

6,250 Posts

27 Jul 2003, 6:57am

Jamiro said
Hi muddocktor.
I've an epox 8hka+ too and I'm interested in buying a new barton processor.
I wolud like to recive recive some informations about your overclock such as the maximum multiplier that the motherboard let you set.
Please contact me on icq (49232507) on msn (joecamola@tin.it) as soon as possible.
(P.S Sorry for my bad English)

Jamiro, welcome to the short-media forums.

The max multiplier that the KHA+ can set on the 2500 Barton procs is 12.5, with the 13 setting in bios. However, you can hard code a higher multiplier on the processor itself very easily, by cutting or blowing some of the L3 bridges. I haven't done this to a Barton proc, but I've remapped the bridges on 3 different Tbred B procs, 2 to a 16 muliplier and 1 to a 15 multiplier. If you have a spare AT or ATX psu, you can easily blow the L3 bridges that don't need to be disconnected as the Barton 2500 uses an 11 multiplier, which has all 5 L3 bridges connected. I just soldered some sewing needles to a spare molex connector on the ground and +5v lines and touched them to the gold dots on the L3 bridges I needed to blow to remap the multiplier. You will see a small spark when the bridge blows. I've also heard of people using a 9v battery to do this but I have no personal experience with using the battery. You can find which bridges you need to blow by using this interactive painting guide.

Reply with Quote

Gargoyle

We can't stop here...

4,685 Posts

» Subscriber

2 Aug 2003, 7:41am

Mmm, Barton goodness...

I wish I knew for sure weather or not my CPU would be stable at a higher multiplier, I'd blast one into it. I think I've about hit my max, though. I'm at 1666 now, and when I get close to 1700 it starts getting quirky. I wish I knew what was causing it.

It's not my RAM, it's got plenty of overhead, and I typically have it at the most relaxed timings. Might be my Radeon? I could always volt-mod the board to get more CPU voltage, but I'm not sure it's that either. I run it at default voltage at 1666mhz, but at 1700mhz it suddenly needs all that I can give it (+0.1).

Unfortunately, while this is my main rig I can't raise the FSB. Now I've got the RAID and SCSI cards in it and I don't want to bork my array and my swapdisk

Once the Athlon 64 comes out, I'll upgrade. Either to an nForce2 or an Athlon 64, but I want to see what Athlon 64 options there are before I go off and buy another XP board, you dig? I am so yearning for an upgrade... I hope the Athlon 64 doesn't take too much longer.

__________________ Main Rig: ASRock 939Dual-SATA2, Opteron 165 @ 9x275=2475, 7600 GT
Laptop: Dell 1520, C2D @ 2000, 8600M GT
Icrontic_11: Asus A7N8X-Deluxe, Barton @ 13x170=2210

Reply with Quote

Gargoyle edited : 2 Aug 2003 at 7:45am .

WuGgaRoO

Rat Catcher

2,351 Posts

2 Aug 2003, 3:02pm

on a kt266....ill be damned

__________________

sig compliments of Dogsoldier due to most people's retinas burning
Now with No Smoke Technology!
[url="http://club.ign.com/b/list/custom?&lid=100018&owner=WuGgaRoO&mode=vown[/URL]

Reply with Quote

Jamiro

New to the neighborhood

2 Posts

6 Aug 2003, 11:40am

Thank you for your replie muddocktor.
Can I was the pin mod http://www.ocinside.de/go_e.html?/ht...md_pinmod.html to select the molti? Barton precessors are unlocked by default? Are you still using a 166mhz bus qithout problems?

Byee..!

Reply with Quote

		Icrontic Forums > Tech: Hardware > Overclocking
Here you are Gargoyle, EP-8KHA+ in action!

Jump to

This Thread	Search this Thread
Print Email	Search this Thread: Advanced Search

Username
Password	Forgot?
Remember me