To talk on Icrontic, just register!

It only takes 30 seconds.

Have an account? Sign in:

Forgot?
 
Reply to Discussion Options
reelbigfish
Punk's not dead
reelbigfish
278 Posts
12 Aug 2003, 2:58am

WinXP won't boot from SATA

Hey guys. I have an Abit IS7 and a Western Digital Raptor. I can get through the entire install of WinXP and it just won't boot. I have the Raptor on SATA 1. All that happens is that the screen stays black right after it says updating DMPI pool. If I install Win2k it will boot from the SATA, but it is extremely slow. With XP when it has to boot from the HDD during install it is quite quick. Then nothing. I have the latest BIOS and drivers. I have no idea why it won't boot. Help!
Reply with Quote
dodo
Genious
dodo
319 Posts
12 Aug 2003, 8:50pm
Do you have a parallel adaptor to try the drive on an IDE channel?
That may isolate a SATA problem.

~dodo
Reply with Quote
TheLostSwede
Where's the ****ing beers?
TheLostSwede
3,212 Posts
12 Aug 2003, 9:04pm
fish,

I take it that you installed the sata drivers during the install right? (the F6 thing) Or are the sata embedded on that board so that you dont have to install the drivers?

Also, check if Apic is enabled in bios. If it is, i suggest you disable it and do a reinstall or perhaps a repair.
__________________ ...
Reply with Quote
keto
SM22 Host
keto
1,829 Posts
12 Aug 2003, 9:28pm
***ALL IMPORTANT*** if you are on the original shipping bios, update to the latest. There are known SATA issues on the NF7-S which are resolved thru bios update. I believe the latest bios rev. is 1.8 dated 7/24 or thereabouts.

Additionally, while I am somewhat reluctant to point you elsewhere for help, there are many and thorough NF7 posts in the Abit section on nForceHQ here
__________________ i'D rAthEr HAvE a fULL bOttLe iN fRonT oF ME tHan a fULL FrONtaL lobOtomy
Reply with Quote
TheLostSwede
Where's the ****ing beers?
TheLostSwede
3,212 Posts
12 Aug 2003, 9:31pm
reelbigfish said
I have the latest BIOS and drivers.

keto said
***ALL IMPORTANT*** if you are on the original shipping bios, update to the latest. There are known SATA issues on the NF7-S which are resolved thru bios update. I believe the latest bios rev. is 1.8 dated 7/24 or thereabouts.

Additionally, while I am somewhat reluctant to point you elsewhere for help, there are many and thorough NF7 posts in the Abit section on nForceHQ here

Even with the release bios, the drives should work, but you will get trouble during boot.
Reply with Quote
keto
SM22 Host
keto
1,829 Posts
12 Aug 2003, 9:50pm
*sigh, scanned when I should have read again* Serves me right for trying to help when I should be working
Reply with Quote
TheLostSwede
Where's the ****ing beers?
TheLostSwede
3,212 Posts
12 Aug 2003, 9:55pm
LOL

FYI, iīm not a damn bit better myself. Sorry for pointing it out. Itīs an ugly thing to do.

On top of that, Fish has an IS7 which is as far from an Nforce you can go. (Itīs an Intel board)

Fish, you havenīt touched the jumper on the drive i hope?
Reply with Quote
keto
SM22 Host
keto
1,829 Posts
12 Aug 2003, 10:46pm
OMG go back to bed keto grumble mumble *dozes off* ;lkjoiupoiu owww my forehead somebody hand me my medication
Reply with Quote
TheLostSwede
Where's the ****ing beers?
TheLostSwede
3,212 Posts
13 Aug 2003, 6:21am
* TheLostSwede slips keto 200 Vicodinīs
Reply with Quote
EQuito
Icrontian
EQuito
933 Posts
13 Aug 2003, 10:36am
Just a thought...

Assuming all IS7's use the same basic bios menus, there are two places where you can enable SATA.

The correct menu for your board (plain IS7, I believe...) is the "OnChip IDE Device" menu -> "OnChip Serial ATA"

The IS7-G has another SATA controller under "Onboard PCI Device" menu -> "Serial ATA controller"
Reply with Quote
reelbigfish
Punk's not dead
reelbigfish
278 Posts
13 Aug 2003, 4:22pm
Hey guys. I will try disabling APIC. And I know it's enabled under onboard peripherals, I will check to make sure it is on elsewhere in the BIOS. Thanks for the tips. The funny thing about it being enabled is that is has to boot off the HDD after the initial files are copied and it does that fine.
Reply with Quote
frothhunter
New to the neighborhood
frothhunter
1 Posts
25 Jun 2004, 2:25pm
When I receive my P4P800 SE from Newegg (in like a day) I am going to experience the same problem, I know.

I dont want to use my slow IDE (7200rpm) HardDrive, I want to use my SATA WD Raptor(10,000rpm) and salvage my old HD to another computer. This being said, I've already begun looking into the problem.

So far, this is what I've found from a different forum, so I hope it helps:

1. make sure "USB keyboard support" and "USB mouse support" are both set to "OS" and not "BIOS" - if either of these are set to "BIOS", it somehow causes the Via RAID BIOS to be disabled during boot, thus preventing the SATA HDD from being recognized as a bootable device
2. make sure "bootable add-in device" is set to "OnChip SATA RAID"
3. make sure "SATA RAID BIOS" is set to "enabled"
4. VERY IMPORTANT - use a normal internal floppy drive when loading Via RAID drivers during windows setup!!! (you may laugh, but I was using a USB FDD, and this seems to have been the main cause for my troubles, as it somehow corrupted the installation)
5. I doubt this last one matters, but set boot device order to: 1. floppy, 2. cdrom, 3. hard disk, and make sure "boot other device(s)" is enabled.


This Thread was posted for the Abit KV7, so I'm not sure the BIOSs are the same... also I encountered some confusion in the post. This person said, make sure keyboard and mouse are set to OS and not BIOS, while another person said it worked when set both to BIOS instead of OS. I'd try the former of the two first.

I don't actually know if this works or not, but just remember not to set up the SATA as a RAID. Also, here's a link to the page i got the info from:
http://www.techsupportforum.com/comp...ic/9974-1.html
Reply with Quote
EQuito
Icrontian
EQuito
933 Posts
25 Jun 2004, 2:34pm
Quoting frothhunter
This Thread was posted for the Abit KV7, so I'm not sure the BIOSs are the same...
The KV7 and IS7 are two completely different boards.
The USB mouse/keyboard issues on the KV7 have been fixed with recently released bios v.15
Reply with Quote
haywirzus
New to the neighborhood
haywirzus
3 Posts
9 Aug 2004, 7:10pm
I find that interesting. I also have an Abit IS7 with a WD Raptor drive and have no such problem. However, with XP installed, I get the following error now every time i startup without the WinXP cd in the drive:

Verifying DMI Pool Data.........
Boot from CD:
Boot from CD:
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER

My Windows XP is of course on the SATA Raptor drive, also in SATA slot 1. Once I put the CD in the drive and restart, Windows XP boots fine....
__________________ ~~Kev
Reply with Quote
sikkid
New to the neighborhood
sikkid
3 Posts
26 Aug 2004, 12:37am
Quoting haywirzus
I find that interesting. I also have an Abit IS7 with a WD Raptor drive and have no such problem. However, with XP installed, I get the following error now every time i startup without the WinXP cd in the drive:

Verifying DMI Pool Data.........
Boot from CD:
Boot from CD:
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER

My Windows XP is of course on the SATA Raptor drive, also in SATA slot 1. Once I put the CD in the drive and restart, Windows XP boots fine....

hey dude,
follow these steps you'll be fine.

1. get a computer that boots to an os aready ie: win95/98/2000 etx.
2. get the mother board cd and locate the drivers.
3. get a floppy disk and format it.
4. find the scsi drivers and create a scsi driver disk this disk is not bootable.
5. remove your ide hdd and boot to the cd for installation.
6 press"f6" and wait till it asks for the scsi drivers then is stall both the controller and the drivers from the floppy (this WILL not work from cd)
7. take fdd out.
u should have no problems anymore.
cheers.
Reply with Quote
oldtimer
New to the neighborhood
oldtimer
1 Posts
4 Sep 2004, 9:26pm

Hello, I have just come across a similar problem.

I am building a new PC, based upon a KV7 motherboard and a 160GB SATA harddrive.
I had not appreciated that the drive would not simply be a straightforward boot up device.

I have tried a number of the suggestions made earlier in this thread, but am stuck with either the DMI pool message, or if trying to install WinXP, a message of "textsetup.oem caused an unexpected error (512) at line 1742 in d:\xpclient\base\boot\setup\oemdisk.c" the message is followed by the inevitable "press any key". This is with an internal DVD and floppy drive installed.

Strangely, putting in a conventional IDE harddrive, with a working WinXP installation from another PC, instead, doesn't seem to help.

Is it me?. I have built a number of PCs from scratch, and never been as stumped now.

Anyone's help would be much appreciated.

By the way, I'm new on the forum, but it looks great.
Reply with Quote
Omega65
EPoX Evangelist!
Omega65
2,891 Posts
5 Sep 2004, 1:33am
I had a simliar problem with a MSI K7D Master-L install. It turned out to be a floppy drive problem was hanging the mobo Boot. Removing the Floppy corrected the problem.

Try disconnecting the Floppy Drive - you never know......
__________________ Moderator: System Core Forum - Got a question??...shoot me a PM

Dell E1705 Core Duo 1.66ghz 1GB X1400 100GB
DFI NF4 SLI-DR - Opty 170 @ 2.5ghz - 7900GT - 2GB Corsair PC4400 Pro - Raptor 74GB
Abit AV8 - X2 4400+ @ 2.5ghz - 2GB G.Skill PC4000 - Raptor 74GB

Heatware: Omega65 150-0-0
Ebay Feedback Omega365 62-0-0

Athlon 64 Comparison: 12 CPUs - Single vs Dual Channel - 512K vs 1MB Cache
Reply with Quote
sikkid
New to the neighborhood
sikkid
3 Posts
5 Sep 2004, 6:12am
Ok what brand is the SATA?

make shure the cd-rom is not scratched.

if the sata is a wd then sorry but you MUST have a working fdd with the sata scsi driver and controller.
you make this with the mobo cd and copy the files to a fdd (it will not read them from any other media)

from what your saying it sounds like a hardware/media issue.

however if the sata is a segate then as far as im aware it should boot without the drivers .

should fly i know this cus my hdd took literally under 30 seconds to format

my system mite be a little underspec to you but i like it. ;-)

3400 + 64
1 gig ddr2 667 ram (1 module)
ATI RADEON R9800XT/256MB DDR/DVI/TV-OUT/AGP8X
GA-K8VT800 (gigabyte)
120gb wd sata hdd
does what i want.

cheers
Reply with Quote
ncc
New to the neighborhood
ncc
1 Posts
13 Apr 2005, 3:29am
Quoting frothhunter
When I receive my P4P800 SE from Newegg (in like a day) I am going to experience the same problem, I know.
I dont want to use my slow IDE (7200rpm) HardDrive, I want to use my SATA WD Raptor(10,000rpm) and salvage my old HD to another computer. This being said, I've already begun looking into the problem.


Thank you, I have similar problem with P4P800-X and Seagate Barracuda 160 GB. I'm going to try your solving
Reply with Quote
gipper
New to the neighborhood
gipper
1 Posts
21 Apr 2005, 7:51pm
ok i have same situation i have resolved with

make sure "USB keyboard support" and "USB mouse support" are both set to "bios" and not "OS"
Reply with Quote
mawibri
New to the neighborhood
mawibri
4 Posts
19 May 2005, 1:04pm
Just a quick one that MIGHT jog someones memory.. I had the same problem with a gigabyte Titan pro board and a Maxtor SATA drive Turns out that I was stupid enough NOT to have enabled SCSI in the gigabyte BIOS as I thought SATA was not SCSI.... Anyway whether it is or not it works just fine now....
Reply with Quote
TVMAgar
New to the neighborhood
TVMAgar
1 Posts
16 Nov 2005, 3:06pm
i have a simalar problem. i have an abit kv7-v and a maxtor 300Gb SATA drive. Bios will detect this drive if i turn SATA RAID BIOS on but then the syetem freezes at the BOOT FROM CD-ROM PAGE, ANY IDEAS?
Reply with Quote
Go Back   Icrontic Forums > Tech: Hardware > Storage
Reload this Page WinXP won't boot from SATA
Jump to
This Thread Search this Thread
Search this Thread:

Advanced Search

Today's Posts - Mark All Read - Contact Us - Icrontic.com - Archive - Top

Current time: 9:16pm (GMT)
Powered by vBulletin®
Copyright ©2000 - 2009, Jelsoft Enterprises Ltd.
Get Vanilla instead. Trust me.