Install Windows 7 from USB

Robert Hallock 1 Apr, 2009 at 2:13pm ET Article published in Tech

Step 3:

Now it’s time to start making that flash drive bootable. Launch a command line and navigate to the directory in which you saved MBRWiz.exe (we saved ours to D:). Once there, invoke the MBRWiz /list command to display a list of drives configured in the system. Be sure to write down the disk number for your flash drive as we have in the figure below.

Note

Windows Vista or Windows 7 users must run the command prompt as an administrator for MBRWiz to function correctly.

MBRWiz has identified our flash drive as "Disk: 4."

Next, issue the MBRwiz /disk=# /active=1 command, where the pound sign represents the disk number of your flash drive.

Setting the flash drive to "/active=1" makes it bootable.

Lastly, copy the Windows 7 ISO’s bootable properties over to the flash drive with the Z:\boot\bootsect /nt60 X: command. In this case, Z: represents the drive letter for the virtual Windows 7 DVD and X: represents the drive letter for your flash drive. Be sure to replace these drive letters with the ones that are appropriate for your PC.

Caution

This command can only be used to copy the bootable bits from an ISO that matches the instruction set of the current Windows installation. Users running 32-bit copies of Windows can only execute this command if a 32-bit Windows 7 ISO is mounted; the same is true for 64-bit Windows 7 ISOs which require a 64-bit OS to be running.

If you’re running a 32-bit copy Windows and want to configure a Windows 7 x64 flash drive, repeat steps 1-3 with a 32-bit Windows 7 ISO, then mount a 64-bit ISO for step 4.

We've copied the bootable bits from Windows 7 on Z: to the flash drive on H:

We've copied the bootable bits from Windows 7 on Z: to our flash drive on H:.

Step 4:

Open Windows Explorer and copy the contents of the mounted Windows 7 ISO to the flash drive.

Final thoughts

With the drive prepped and the files copied, it’s time to configure your BIOS to boot from USB and let ‘er rip! Installing Windows 7 from USB takes about 30 minutes depending on your system configuration. Remember to leave your flash drive connected until the installation completes, and you’ll be all set.

« Previous

Pages: 1 2

Comments

1 Apr 2009 ~ 6:58pm Trumansnare Awesome,
Nice tutorial
Im gonna give this a go.
Thank you
1 Apr 2009 ~ 7:12pm BlackHawk Thanks. Gonna try it out on all the machines in the house once RC1 rolls out.
2 Apr 2009 ~ 7:30am Everton how big a drive is required?
2 Apr 2009 ~ 9:48am Thrax 4GB or better.
6 Apr 2009 ~ 5:32pm Dennis My Command Line always starts with C:\Documents and Settings\Name>

How do I clear it and make commands with other drives?
6 Apr 2009 ~ 5:42pm BuddyJ cd C:\

"cd" is the command for change directory. It's what you need to switch to whatever location you're looking for.
10 Apr 2009 ~ 2:24pm Mehdi thank you for comprehensive tutorial . Do I still have my xp after installing in this way?
10 Apr 2009 ~ 3:16pm Thrax You will have XP if you tell Windows 7 to create a partition out of free space. If you choose to reformat, you will not have XP.
19 Apr 2009 ~ 11:56am Zaphire It's much easier to do it with UltraISO.
You load the install DVD or an iso of the install DVD you may have downloaded into UltraISO. Then simply use the 'Bootable' menu option to 'Write Disk image...' and having set which drive your USB Key is, press 'Write'.
You can also check the box to 'Verify' your write.
You are effectively doing what you do when you burn an ISO to a DVD but in this case it's a one step operation to 'burn' a bootable USB key without having to format it, use the HP or MBR tool or Diskpart etc. You can overwrite a used key or do this on any new key.
And you can do it in XP, Vista or Win 7.
5 May 2009 ~ 8:32am primesuspect Ultra ISO also costs money.

This method is free. So why would you pay $30 for something you can do for free with the above tools?
5 May 2009 ~ 9:18am Rob You can do it on the Ultra ISO trial, so your point is moot.
5 May 2009 ~ 10:17am Thrax And when you want to do it again in the future? Right, you'd have to reformat to circumvent the trial limitations.
29 May 2009 ~ 3:01pm jokerz4fun Thrax great post! I might give this one a try.
30 Jun 2009 ~ 9:02am Tb Hi there - I hardly ever leave posts anywhere, but I just wanted to say *thank you so much* for your easy to follow guide on making a bootable usb using xp. I searched for hours to find a method that wasn't totally incomprehensible due to the use of jargon that I don't understand. Thanks again, I really appreciate it.
19 Jul 2009 ~ 5:21am Shay when I issue the command g:\boot\bootsect /nt60 e:

I get

Target volumes will be updated with BOOTMGR compatible bootcode.

Drive e: maps to volume \\?\Volume{910a560e-4b52-11de-b1ba-0016418aa708}.

This volume does not appear to connect to any disk partitions. Volume bootcode

is always unused in the absence of associated partitions.

any help would be great
7 Aug 2009 ~ 7:07pm Ranic Will doing this wipe my hard drive?
7 Aug 2009 ~ 9:21pm Thrax Creating the USB stick will not wipe your hard drive. Installing Windows 7 will wipe your hard drive.
13 Aug 2009 ~ 2:41am ss hi..
when i try to do MBRwiz /disk=2 /active=1 (in my case it is 2) it gives an error "invalid partition selected".
please tell me what to do?
14 Aug 2009 ~ 9:52pm Ludvig I Have a 32bit version of XP but my Windoes 7 is a 64bit. and it says caveat isent a command
18 Aug 2009 ~ 11:58pm missoz I did everything u said but when I try to boot from the flash drive I get "BOOTMGR IS MISSING". What should I do?
19 Aug 2009 ~ 12:46am missoz tried it again now it says DISK ERROR
21 Aug 2009 ~ 7:11pm j0k3r It is necessary to Format Flash with NTFS.
I heard this makes the drive slow.
Will formatting to Fat32 work?
21 Aug 2009 ~ 7:23pm Snarkasm NTFS doesn't make the drive slow. It's a different filesystem, that's all, and it lets you put files larger than 4GB on the drive.
27 Aug 2009 ~ 11:04am Yotam WOW, I've tried 5 different tutorials and this is the only one that actually worked for me, thank you very much.
27 Aug 2009 ~ 11:10am Thrax You're very welcome, Yotam! I ran into the same issues when the beta was released, and I decided that I'd had enough, so I wrote one that I knew would work because I used it!
27 Aug 2009 ~ 11:25am Ryder

Snarkasm wrote:

NTFS doesn't make the drive slow. It's a different filesystem, that's all, and it lets you put files larger than 4GB on the drive.

It will slow down a flash drive Snark. Most flash drives, due to the nature of the Nand, will find FAT32 the fastest/speediest. Now, if you can get it formatted NTFS with 32K blocks.. that should be close to the same speed.
27 Aug 2009 ~ 12:42pm Snarkasm Can you quantify the degree of slowdown, if you don't mind? Is it actually worth mentioning at all?
27 Aug 2009 ~ 12:53pm Ryder Usually 3 - 5 MB/s on most chipsets (real data transfer).
27 Aug 2009 ~ 12:53pm shwaip http://www.testfreaks.com/blog/information/usb-flash-drive-comparison-part-2-fat32-vs-ntfs-vs-exfat/

ntfs loses big in sisoft, but it's only barely slower in other tests.
27 Aug 2009 ~ 12:56pm Snarkasm Gotcha. Thanks folks.
4 Sep 2009 ~ 6:08am longxin Fantastic, just clearing up my 32G stick.

Question, do you have a 'working' tutorial for a multi-boot XP+Vista+7+2003+2008 x32 and x64 "ultimate windows install USB stick?"

lx
4 Sep 2009 ~ 10:07am Thrax I do not have such a tutorial, but I have a decent idea as to how that might be accomplished. I'll look into it! Thanks, longxin!
6 Sep 2009 ~ 3:47pm Josh22 I have tried this and 2 other ways to make a bootable usb for win 7 installation, but it never boots, it just stucks on the flashing _ . What can I do so I can finally install windows 7???
7 Sep 2009 ~ 7:56am longxin Thanks Robert. Look forward to seeing that Ultimate Windows Installer USB stick tutorial!

This works like a charm! thanks again.
Lx
18 Sep 2009 ~ 6:27pm Yes@ YES WORKED GREAT THANKS!
29 Sep 2009 ~ 3:52pm Matej Oh this is helpful guide. Awesome. Thanks dude!
2 Oct 2009 ~ 9:45pm Guigwime Unfortunately, this didn't work for me. I followed it, but when I boot, I just get "Reboot and Select proper Boot device or Insert Media in selected Boot device and press a key." Now, I know that it detects it because the bios changed the name from "Removable Disk" to "Fanthom Drive" but it seems it still doesn't feel like booting. I did do the mbrwiz tool thing, so I got the bootsect. So I don't know what's going on
2 Oct 2009 ~ 9:46pm Thrax This guide works perfectly on any computer capable of booting a USB stick. So either your PC is one of those PCs that can't, or you made a misstep somewhere.
23 Oct 2009 ~ 12:28pm Eric Hi there!

I did whats on the tutorial and when i boot from the usb stick i get 'read disk error'. I've set the boot priority to usb and i even flashed the bios just to make sure. My system is a P4 2.4 , 1GB ram and the mobo MSI PT8 Neo-V.
I can't figure out what the problem could be. Please help!

Thanks
29 Oct 2009 ~ 1:29pm Fern Hello!

How is it going with the tutorial for a multi-boot XP+Vista+7+2003+2008 x32 and x64 "ultimate windows install USB stick?"
9 Nov 2009 ~ 10:21am KHALIL Hi there..

I followed all of the above steps but when I restart and after company logo there is a cursor flashing and nothing happenx(setup not starting..)
18 Nov 2009 ~ 3:31pm photodude Guess I'm out of luck for doing this since I have a download version which is just an .exe file

maybe I'll have to wait for my backup disk so I'll have an ISO (unless the exe creates an ISO but I don't dare run it yet as I plan to keep my old drive on another system since it's a full install and I have a different license I can use for the upgrade version I got a sweet deal on)
18 Nov 2009 ~ 3:32pm Thrax @photodude: http://www.digitalspy.co.uk/forums/showthread.php?t=1151639
19 Nov 2009 ~ 11:33am photodude Thanks for the link @Robert.

Looks like the .exe and two boxfiles, is an extractor program and does not have an iso in it.

I did get an ISO download after an email to customer service. Next step getting a hard drive and the USB ready.
1 Dec 2009 ~ 4:13pm Robin Nilsson I tried to install win7 with this guide but when I get to step 3 and try to use the command Z:\boot\bootsect /nt60 X: i get this message: the system cannot find the path specified. I write F:\boot\bootsect /nt60 G: , where F: is the place where i mounted the disk in daemon tools and G: is the place for my USB-stick... what do I do wrong?
8 Dec 2009 ~ 5:12am unknown222222 TNX TO THE MAN/WOMAN/PEOPLE WHO POSTED THIS GUIDE, IT WORKS, NOW I HAVE WINDOWS 7 hahahaha!!!!!!!!!
31 Dec 2009 ~ 7:47am tejadeep thanks a lot it was really helpfull but the bootsect command can be skipped check the othere sites for more procedures
18 Jan 2010 ~ 10:09pm confused i have managed to follow your steps and created a USB bootable disk.
i am using WinXp.
when i boot my comp with the USB, it states that the bootmgr was incorrect.
26 Jan 2010 ~ 6:25pm problemchild I tried but encountered various errors. After I try to set the drive/partition as active, windows will no longer allow me to use it, saying it isn't formatted, but it won't let me format it again either.

I used the HP software and it would allow me to format it as NTFS, and UltraISO burned it perfectly. I understand the free vs trial debate, but use what works!
5 Mar 2010 ~ 5:07am Bvn TY
5 Mar 2010 ~ 5:11am Snarkasm YW
12 Mar 2010 ~ 2:28pm Ivinio it looks like you had windows Vista, would it work if i have windows XP?
12 Mar 2010 ~ 2:30pm Ivinio Please reply to my email ivinio21@gmail.com i want to know if it works with windows xp pro. Thanks.
12 Mar 2010 ~ 2:37pm Thrax It works on XP.
26 Apr 2010 ~ 5:21am Cherimoya Eihn I have no boot menu on my laptop.
And installation Windows 7 DVD was scratched.
What i did was:
1) download windows 7 installation ISO;
2) unpack it on flash drive;
3) boot from any installation CD/DVD (just to get close
to command promt);
4) format c:;
5) copy contents of flash drive to c:;
(xcopy f:*.* c:);
6) reboot.
The PC will boot from c: as it was some DVD and will actually install Windows on itself.
14 May 2010 ~ 7:42pm amit Hi there,

Just wanted to thank for this article. After following it windows 7 was up and running on my portable with in 25 mins. Formating my existing drive was taken care by win 7 during installation. Only driver I had to update was nVidia GForce.

Thanks,
ak
5 Jun 2010 ~ 7:22am cyhex here is a very simple way of doing that:

dd if=windows.iso of=/dev/usb

for windows users get dd from the net. All *nix osx should have it installed by default.
24 Jun 2010 ~ 5:28am Andrew Using Windows XP SP3 x86. Trying to make bootable USB of Windows 7 x86. When I issue the MBRwiz /disk=# /active=1 command, I don't get the message "Partition successfully ACTIVE". I tried active=0 command, then retried active=1, but still not working. It doesn't boot after completing all steps. I have USB Boot capability in BIOS.
17 Jul 2010 ~ 11:22am Manoj We need to first identify the flash disk, so start by running MBRWizard with the /list command: mbrwiz /list . After locating the flash drive, make note of the Disk # associated with the flash disk. Now, execute the following command, making sure the /disk=x variable corresponds to the flash disk #:

MBRWiz /Active=1 /Disk=x
25 Jul 2010 ~ 9:15am Manoj But finally i get an Disk Read error...

OS: WinXP
MOBO: Asus MT2NPVMX
Trascend 4GB USB
12 Aug 2010 ~ 9:06am Helix I've tried this several times even using the Windows USB/DVD tool and it continually spits 'Disk Read Error' at me ... Why?!
12 Aug 2010 ~ 12:53pm primesuspect You probably have a bad disk
19 Aug 2010 ~ 12:23pm kiks hi. i am not tech savvy and i need your help. i have a new computer set at home and it has no OS. completely new. specs are core2duo e7500, 2gb ram ddr2 apacer, asus p5kplam epu board, dvdr writer,320gd hdd and 1gb geforce 9500 vid card. i don't know it it's fast. it is for documentation purposes. anyway, i have my windows 7 ultimate installer in an 8gb-usb drive. how do i install the OS? because in this guide, it is for computers with existing programs. thanks. badly need your help, guys. i need a step-by-step process. thanks again
19 Aug 2010 ~ 1:31pm Ryder Put the USB stick in the PC, boot the PC into the bios (usually you press delete to enter the bios, but it may be F2, F10, or F12 also), make sure the USB stick is the 1st boot device, then save and reboot the system.

Once it boots, follow the prompts to install Windows like you normally would.
19 Aug 2010 ~ 2:22pm kiks Thank you, RyderOCZ. OH, this is my first time to ever install an OS. Obviously scared. If it fails, may I be able to do it again?

As they mentioned above, I need to download some ISO softwares. I do not need to do that since my set is new, do I?

I also need to have a partition in my 320gb hdd into 160gb each. I think that happens in the installation process and I have to check the OPTIONS part. Please correct me if I'm wrong.

Thank you.
19 Aug 2010 ~ 2:32pm kiks Geez... Lost my follow up comment.. Anyway...

Thank you for that RyderOCZ.
It is my first time ever to install an OS.

If by any chance the installation would be a failure, it is possible to do it again, right?

Also, I would like to have 2 parts for my 320gb hdd into 160gb each. One for the program Files and the other for my personal files. I think it will appear in the Windows Installation as I go along, right? Somewhere, it has OPTIONS. Just can't picture it out the way my friend described the process to me.

"Once it boots, follow the prompts to install Windows like you normally would."
> Do I need to boot the CDRom and the HDD as well or what?

Thanks. I am taking down notes.
19 Aug 2010 ~ 2:38pm fatcat not to take away from Thrax's guide, which is awesome in it's own right...

but I just used this last night:

Windows 7 USB/DVD Download Tool\

You DO need your Windows 7 .ISO you DID download from Microsoft when you BOUGHT windows 7 online.
19 Aug 2010 ~ 5:13pm kiks How will I be able to use Windows 7 USB/DVD Download Tool\ when my computer is brand new? it has no softwares at all.
5 Nov 2010 ~ 12:52am nkspro Thank you for your guide. Here is very simple plan:

1. download the hp usb format tool
2. Format as suggested in this guide
3. Use the Windows 7 USB tool
4. Bingo, no error. Try it, it would work.
24 Jan 2011 ~ 5:16pm galaga thanks EZ as
22 Feb 2011 ~ 4:14am audreygreen How much space is required. I have an 8GB memory stick, but it has only around 4GB left...Can't delete important files though. Is that enough to install win 7?
23 Feb 2011 ~ 1:37am akash "MBRwiz /disk=1 /active=1 "command gives
Error 105: "Invalid or incomplete switch: /disc=1".....any idea how to resolve this?
23 Feb 2011 ~ 1:38am Thrax It's /disk=1, not /disc=1.
14 Apr 2011 ~ 3:45pm DeathKnight hey Thrax please help
every time i tried to do first step cd Desktop/MBRWiz it told me invailed or incomplete switch: /
what should i do please help i need this win 7 badly
14 Apr 2011 ~ 5:49pm Tushon
if you saved the file in the a folder on your desktop called mbrwiz, your commands would look like this
```
cd %username%\Desktop\MBRWiz
mbrwiz /list
```
20 Apr 2011 ~ 12:58pm confused geek Hey, I'm also having the "error 105: invalid or incomplete switch: /active=1" yes I spelled disk correctly, it looks like it's because of the 'command line parameters may have been changed in version 3.0" (MBRWiz) Is the fix to get the older version of mbrwiz?
20 Apr 2011 ~ 1:03pm Tushon

confused geek wrote:

Hey, I'm also having the "error 105: invalid or incomplete switch: /active=1" yes I spelled disk correctly, it looks like it's because of the 'command line parameters may have been changed in version 3.0" (MBRWiz) Is the fix to get the older version of mbrwiz?

I think you probably need to drop the =1 on /active

Source
20 Apr 2011 ~ 1:09pm confused geek I actually got past that, running v2.0b right now in vista with the download that's for xp/98 but I want to install 64bit windows 7 on a new machine, and this current (old) build is on 32-bit vista. How can I create a 64-bit ISO as you stated before step four?? the help is greatly appreciated
20 Apr 2011 ~ 3:38pm Tushon

confused geek wrote:

I actually got past that, running v2.0b right now in vista with the download that's for xp/98 but I want to install 64bit windows 7 on a new machine, and this current (old) build is on 32-bit vista. How can I create a 64-bit ISO as you stated before step four?? the help is greatly appreciated

Thrax wrote:

If youâ€™re running a 32-bit copy Windows and want to configure a Windows 7 x64 flash drive, repeat steps 1-3 with a 32-bit Windows 7 ISO, then mount a 64-bit ISO for step 4.

He states in the preparation that you already need to have an ISO in your possession. We can only recommend legally obtaining such things, but what matters the most is not the ISO you get, but that you have a valid key. Use your search button.
12 Jun 2011 ~ 11:02am Chris Ive noticed with a lot of you guys, make sure ever comman line you type is exact same as file you looking for. everthing is case sensative, like when your working the MBRWiz file a lot of you are typing MBRwiz which is wrong cause in the file name the w is capital...this guide works great if you use common sense and follow the guide
22 Jun 2011 ~ 10:08pm BobCov Don't know if this is valid, but it worked for me. I used PeToUSB (google it)with option enable LBA and enable disk format, then used magiciso to mount the win7iso, extracted bootsect.exe and used bootsect /nt60 F: option. Then used copy to copy the contents of the iso to the drive. It was a 4GB flash and it has 1.4gb free.
11 Jul 2011 ~ 2:46pm Vetaz Lets hope this will work!:) I am now copying the iso^^ It gonna take about 45mins:( ANyway thanks for the help and i hope it will work since, in this tutorial, i have gotten the furthest:D
18 Jul 2011 ~ 8:58am gunraykilla i did everything right, when i reboot my bios just loads like normal, even if its set to boot the removable disk first. i have xp 32 bit sp3, brand new mobo
18 Jul 2011 ~ 12:23pm Tushon

gunraykilla wrote:

i did everything right, when i reboot my bios just loads like normal, even if its set to boot the removable disk first. i have xp 32 bit sp3, brand new mobo

Then you didn't do something right ...
26 Aug 2011 ~ 5:01pm keriko thank you very much for this article. it's the first decent, step by step tutorial for the slightly less tech-genius that i've read. massively helpful and has really made my win7 tablet install a pleasure. thank you.
11 Sep 2011 ~ 5:19pm Manuel Dude, thanks... It was straight forward, it is a great tuto!!!
19 Oct 2011 ~ 5:14am UraniumX Thanks man this was really helpful. Worked like a charm on my old crappy windows XP OS. My DVD rom was out of order so have been trying a whole lot of methods to make my pen bootable, and at last I found this! Long live bro
19 Feb 2012 ~ 8:44pm Kevin05 The (MBRWiz/list) command will not work! When I type it in, the following comes up: "'MBRWiz' is not recognized as an internal or external command, operable program or batch file." What do I do? I'm running Windows XP.
24 May 2012 ~ 6:45pm JEDAN45 First open cmd in run and use cd to go to the directory where you saved MBRWiz and type MBRWiz /list then so on and on.
23 Aug 2012 ~ 10:54am Justin To anybody have trouble with MBRWizard: Make sure you check the online documentation for changed commands!! I had to change MBRWizard /Disk=1 /Active=1 to read MBRWizard /Disk=1 /Active

It didn't work in the format specified in the tutorial, so make sure you check your documentation! Other than that, thanks for the tutorial!
23 Aug 2012 ~ 11:03am BlackHawk I know this is old but MS has a utility out.

http://www.microsoftstore.com/store/msstore/html/pbPage.Help_Win7_usbdvd_dwnTool

Worked perfectly when I used it to install 7 on a nettop.